Datagest
SoftwareGibitre Software
PlatformSmart Test
IdentificationRheoCheck
SoftwareMooney
Check - SoftwareDensity
Check - SoftwareHardness
Check - SoftwareTensor
Check - SoftwareTR_Test -
SoftwareBrittleness
Check -
SoftwarePressCheck
SoftwareCompression
Set -
SoftwareCompany Connection
SoftwareGibitre
Software InstallerMaintenance and Calibration ServiceISO 17025 Accredited CalibrationRemote Assistance Service
Support request form
Italiano
English
Español
Français
Deutsch
Português
Polskie
Čeština
Magyar
Русский
Türk
中文
日本人
한국어
Arab
The Compression Set tester from Gibitre Instruments performs fast and reliable tests in accordance with ISO 815, ASTM D395-B, and DIN 53 517. The 12-specimen capacity and the 2- or 3-plate configuration make it easy to adapt the procedure to different materials.
The aluminum carrying handle, 3-bolt closure, and adjustable base speed up test preparation.
The calibration report detailing the plate roughness and spacer thickness verifies the instrument’s compliance with standards and ensures repeatable results.
Circular anti-slip spacers and rubber feet simplify specimen handling and stabilize the measurement.
Accessories complete the process: a 0.001 mm thickness gauge compliant with standards and software for data collection and calculation of permanent deformation; spacers with custom thicknesses available upon request; a clampable base for rapid setup of the device.
A choice for those seeking reliable instruments that combine operational efficiency and data quality in Compression Set testing.
This Compression Set device complies with ISO 815, ASTM D 395 Method B, DIN 53 517 standards.
The Compression Set Test methods are intended to measure the ability of rubbers to retain their elastic properties at specified temperatures after prolonged compression at constant strain (normally 25 %) under specific Temperaure and Deformation conditions.
For rubber of nominal hardness within the range 10 IRHD to 80 IRHD 25 % strain is normally used. For hardness of 80 IRHD and above, a lower compression strain is used: 15 % for a nominal hardness from 80 IRHD to 89 IRHD and 10 % for a nominal hardness from 90 IRHD to 95 IRHD.
• Usable area optimized for 12 specimens
• Instrument setups with 2 or 3 plates
• Aluminum handle for one-hand manipulation
• 3-bolt lock for quick preparation
• Support base for screwdriver use
• Chrome-plated plates with standard roughness
• Calibration report for roughness and spacers thickness
• Circular anti-fall spacers
• Rubber feet
To perform a test:
1) Insert the samples between the test plates
2) insert the 3 spacers requestd to obtain the expected deformation
3) Close the bolts until the plates come in contact with the spacers to apply the expected deformation
4) Place the whole device in an oven at the set temperature and for the desired test time
5) Remove the device from the oven and mesure the permanent deformation using the procedure described in the standards
The software allows to acquire the thickness measurement from the comparator (connected via USB cable) and to calculate the results of the Compression Set tests.
In particular, the software allows you to:
• identify the specimens
• select the specimen processing method that was used
• enter the initial and final thickness of each specimen and the thickness of the spacer used
• Calculate the Compression Set value obtained in compliance with the standards
• Compare the result with the tolerance limits and save the results in the Gibitre SQL standard database
• Produce Reports and Statistics.
The Compression Set device is equipped with a unique identification label and is supplied with a Calibration Report with traceability to the reference instruments used.
The Calibration Report includes the measurements of:
• Surface roughness of the device in accordance with the requirements of the standards.
• Spacer thicknesses measured in 3 points.
Compression set devices require frequent movements and manipulations and must be placed in stoves. Being able to manipulate the instrument with one hand is certainly an advantage.
The solid anodized aluminum handle improves handling but does not increase the volume occupied in the stove.
The size and thickness of the plates have been designed to ensure the necessary rigidity while maintaining a low weight: 11.5 kg for the 3-plate device and 8 kg for the 2-plate device.
The device allows the closing of the upper plate using only 3 bolts. The bolt head is recessed into the base plate to avoid the use of two wrenches.
3-bolt closure reduces preparation time by 25%.
The 3-plate model is optimal for performing large quantities of tests in one run, allowing up to 24 ISO 815-1 Type A specimens to be tested simultaneously.
For changing control needs, the intermediate plate can be added or removed.
The total weight of the assembled device is 11,5 kg
The 2-plate model is versatile and light, allows you to test up to 12 ISO 815-1 Type A specimens simultaneously and is optimal for laboratories where specimens arrive in staggered fashion.
The total weight of the device is 8 kg.
The usable surface of the devices allows to test up to 12 ISO 815-1 type A specimens.
A rectangular device with the same surface could only accommodate 8.
The assembly and opening operation of the device can be tiring and not without risks.
The support base, specially designed to be locked in a vice, ensures that the device does not move during operations and allows you to use the automaic screwdriver to avoid the use of wrenches: a pit stop for your Compression set.
• Mould for sample prepation
• Thickness meter for the measure of sample thickness
The reduction in the number of sharp and angular surfaces helps to reduce the risk of shocks and noise during numerous manipulations of the devices.
The shape of the equilateral triangle device and the thickness of the 18 mm plates eliminates the risk of deformation of the plates even with a large number of specimens with high hardness and guarantees to apply the same deformation to all specimens.
The instrument is totally developed and produced in the plant of Gibitre Instruments in Italy.
All the mechanical parts are produced in the company workshop using modern CNC machines.
Components and sensors from well-known brands are selected in order to ensure the maximum reliability in the measures
Internal trained personnel takes care of all the production stages: assembly, start-up, calibration, packing, shipment and installation.
