DensityCheck_10 Software

One of the key characteristics to make an instrument functional is the simplicity in identifying the tests to be carried out.
The new Gibitre release 10 programs allow you to:
• Reduce the time for insertion
• Do not make identification errors
• Identify the correct test procedure for the product
• Have a complete traceability of the archived Results.

Enter the list of tests to be performed by manual selection or barcode reader.
Then apply the specimen to the magnetic stand.
Finished !
The instrument:
● Waits for the specimen to be applied
● Measures your weight
● Raises the glass with the comparison liquid
● Measures the volume
● Calculates density
● Lowers the glass
● Compares the result with the tolerance limits
● Saves the result in the SQL database
... and is ready for the next specimen
All in about 10 seconds.

The calibrated temperature probe inside the beaker measures the temperature of the reference liquids.
The software corrects the density of the test liquids based on the temperature and uses the correct value for the measurements.
Each result is saved together with the temperature measurement and the real density of the comparison liquid.
Seasonal variations in density measurement with changing laboratory temperature are just a memory!

Aging tests on Rubber products are performed according to international standards (ISO 1817, ASTM D471, etc) to evaluate the capability of the product to perform correctly in use conditions.
The aim of this test is to measure the Mass and Volume Percentage variation after the aging of the samples and to compare the results with the expected tolerance limits.
The instrument performs this operation automatically
In order to measure the Mass and Volume variation of the samples, you need to:
● Prepare at least 3 samples
● Perform a test with the instrument on the samples before aging
● Age the samples at the requested aging conditions
● Select the identification of the tests originally made on the samples from the List of Tests with Pending Treatments
● Repeat the test on the samples
The software will do the rest:
● Calculates the Percentage Mass and Volume variation
● Compares the results with tolerance limits for the product and for the treatment selected
● Stores the results to the SQL Database

This function permits to perform easily the sequence of operations requested for the measure of the samples before and after the Abrasion Resistance test described by ISO 4649 and ASTM D5963 standards.
The software performs the following operations:
● Recording of the level of abrasiveness of the paper by differential weighing of the certified specimen
● Measurement of the Volume and Density of the specimen to be submitted to abrasion test
● Measurement of the volume of the specimen following the abrasion test
● Automatic Calculation of Volume Loss
● Automatic calculation of the Abrasion Resistance Index
● Automatic recording of the results in the Gibitre instruments SQL database

Version 10 programs make the following options available for preparing test reports:
• Selection of printing language
• Company logo insertion
• Print a single test / a Group of tests
• Print of Test Curves
• Print Numerical Results
• Print the Limits of Tolerance
• Print Statistical Results
• Print Legend with explanation of results
• Print the Operator Signature
• Print Customized Notes
• Preparation of PDF file

The program integrates a REPORT EDITOR that allows you to completely edit the report and prepare fully customized report formats

The results and test curves of all the tests carried out are saved in the Gibitre SQL database and are available through the Datagest program.

Datagest is the Laboratory Information Management System (LIMS) which is always installed in combination with all Gibitre instrument-control programs.
The program is the collector for all the test result produced with the instruments connected and permits to manage the common Archives used by the instruments (Product List, Customer List, Tolerance limits, Order List, etc)

The Instrument Configuration page allows you to adapt the operating modes to your needs.
The configurations are saved and applied with each new opening.
The configurations are editable based on the operator access level.

The Datagest program allows you to define specific tolerance limits for each Product, Customer, Test Procedure and Aging Treatment.
For each result to be calculated, tolerance limits and alarm limits can be defined.
The comparison between the results and the tolerance limits is carried out automatically at the end of each test: the test results are colored (Green, Yellow or Red) based on the outcome of the comparison with the limits.
The outcome of the check is saved in the database together with the results.

The programs automatically process the statistical analysis of the tests in progress by calculating:
• Maximum
• Minimum
• Average
• Median
• Standard deviation
• Cp
• Cpk
In addition, the Gaussian curve relative to the results is shown together with the tolerance limits to immediately highlight the progress of the tests in progress.
The Datagest program allows you to process more detailed statistics related to the saved results and to represent X and R Charts by grouping data by order, batch, batch, date, etc.

The SQL database that is installed together with the tools contains predefined test procedures for each type of Gibitre tool.
Test procedures contain:
• settings for automatic instrument adjustment
• the list of results to be calculated on the basis of what is required by international standards.
The Datagest program allows you to: copy, modify, create the Test Procedures to adapt them to your needs.

Test procedures can be exported and imported. This allows Gibitre Remote Support to support you in the preparation and testing of customized Test Procedures.

All the programs produced by Gibitre are multi-language and allow the operator to select the language of use.
The test report can be produced in the desired language regardless of the language of use of the program.
The languages available at the moment are: Italian, English, German, French, Portuguese, Russian, Chinese, Japanese, Turkish, Polish, Czech

• Programs can be installed on standard PCs with WINDOWS 10 or 11 OPERATING SYSTEM.
• The CONNECTION between the instruments and the PC is made using the USB CABLE supplied with the instrument.
• The programs are COMPATIBLE WITH ANTIVIRUS, and other programs installed on the PC.